We also offer our kits with a Coolerguys programmable thermal controller with LED temperature display as well as with no controller at all (always on, great to use with switched AC powered outlets)
All parts in our kits come with a 3 year replacement warranty at no cost to you
This particular *kit is for a single fan unit meant to cool your cabinet, multimedia center, aquarium, home grow op, brewing project or whatever else that may need cooling, the only limit is your imagination!
This kit can move 30 cubic feet (WxHxD) of air per minute (CFM)
Can be mounted on any side of a cabinet, where room permits (cutout dimensions below). Insert completed cooler assembly in hole and attach with appropriate screws. Fan can be set to be either an intake or exhaust, simply mount the fan to the bracket pointing in the desired direction before installing (if you are looking at the label the air will flow towards you)
If you need additional information you can contact us!
(1)Ultra Quiet & Reliable Coolerguys Dual Ball Bearing 92mm 3pin 12v Fan
With Dual Ball Bearings this Fan is rated to last 60,000+ hours running 365/24/7 (over 7 years!)
The fan has a 12" (300mm) long cord, if you need to extend this length we have extensions here
Coolerguys Programmable Thermal Controller with LED Temperature Display
This controller comes with a 32" long waterproof probe, place where you'd like to monitor the temperature, when the temperature reaches the temperature you have programmed as the "On" setting the fan and anything else plugged into the unit will be activated until the temperature falls below the programmed "Off" setting.
It natively supports up to 4 3pin connections (12v only) but can handle more with the appropriate splitters (maximum 3A).
Comes with our shelf mount bracket so you can mount the display if you'd like.
Click here to see our probe replacements & extensions
Temperatures above are (+/- 1° F) / Programmable range of 40F (4C) to 145F (63C) / LED display can be toggled on/off
All necessary screws, cables, and fasteners are included to assemble, install and operate this unit.
If you'd like to add additional brackets and fans to this kit you can find them here, non-thermal controlled kits only have enough ports for the fans which come with it, the standard thermal controlled and programmable controllers have 4 native ports, if you need more ports for fans we have adapters here
Need an anti-static workplace? what about zip-ties, cable anchors or sleeving to help clean up your installation?
Check out our recommended installation and finishing items here.
Completed Fan and Bracket Dimensions when assembled using the included parts:
4.75" x 4.75" x 1.38" (120 x 120mm x 35mm)
3.75" x 3.75" (95 x 95mm)
General Instructions for CabCool Cabinet Cooler Kits (574 kb pdf)
Total Kit Contents:
(1) Coolerguys 100-240V AC to 12V DC Power Supply
(1) Coolerguys Ultra Quiet 92x92x25mm Dual Ball Bearing Low Speed Fan
(1) Coolerguys Programmable Thermal Controller with LED Temperature Display
(1) Black 92mm Wire Fan Grill
(1) Black 92mm Honeycomb Grill
(4) Fan nuts and bolts
(4) #6 - 1/2" black Cabinet screws
*This is a kit and some assembly is required.
Operation Voltage: 6.5~13.8 Volts
Input current: 0.09A
Operation temperature: -10 to +65 C
Storage temperature: -40 to +70 C
RPM: 1500 +/- 10%
Connector: 3 Pin w/ 12" Tail
Life: 50,000 hours (Nearly 6 continuous years)
Lifespan is based on the operating temperature of 95F (35C)
We trust in our products at Coolerguys and test everything that is sent out! We happily extend a three-year replacement warranty to all our Coolerguys branded products.